• Previous
    NEO -7N 7N Flight Controller GPS Module with 3 Axis Compass for Pixhawk APM 2.6
  • Next
    Ublox M8N GPS Compatible with DJI NAZA Lite V1 V2 Flight Controller

NEO M8N HIGH PRECISION GPS BUILT IN COMPASS FOR APM AMP2

In Stock
4,999.00
Product Code: RM2466

Delivered In: 15-20 Business Days

Description

NEO M8N HIGH PRECISION GPS BUILT IN COMPASS FOR APM AMP2

NEO-M8N Flight Controller GPS Module with Shell for APM APM2.52 APM 2.6

A new generation Ublox GPS NEO-M8N,with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy,support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol and mode or more.

  • - GPS Chip parameters:
  • - Receiver type 72-channel u-blox M8 engine
  • - GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
  • - SBAS L1 C/A: WAAS, EGNOS, MSAS
  • - Galileo-ready E1B/C (NEO-M8N)
  • - Nav. update rate1 Single GNSS: up to 18 HZ
  • - Concurrent GNSS: up to 10 Hz
  • - Position accuracy2 2.0 m CEP
  • - Acquisition2 Cold starts: 26 s
  • - Aided starts: 2 s
  • - Reacquisition: 1.5 s
  • - Sensitivity2 Tracking & Nav: –167 dBm
  • - Cold starts: –148 dBm
  • - Hot starts: –156 dBm
  • - Assistance AssistNow GNSS Online
  • - AssistNow GNSS Offline (up to 35 days)3
  • - AssistNow Autonomous (up to 6 days)
  • - OMA SUPL & 3GPP compliant
  • - Oscillator TCXO (NEO-M8N/Q),
  • - Crystal (NEO-M8M)
  • - RTC crystal Built-In
  • - Noise figure On-chip LNA (NEO-M8M). Extra LNA for lowest noise figure (NEO-M8N/Q)
  • - Anti jamming Active CW detection and removal. Extra onboard SAW band pass filter (NEO-M8N/Q)
  • - Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
  • - Supported antennas Active and passive
  • - Odometer Travelled distance
  • - Data-logger For position, velocity, and time (NEO-M8N)

  • - Operating temp. –40° C to 85° C
  • - Storage temp. –40° C to 85° C (NEO-M8N/Q)
  • – 40° C to 105° C (NEO-M8M)
  • - RoHS compliant (lead-free)
  • - Qualification according to ISO 16750
  • - Manufactured and fully tested in ISO/TS 16949 certified production sites
  • - Uses u-blox M8 chips qualified according to AEC-Q100

  • - Supply voltage 1.65 V to 3.6 V (NEO-M8M)
  • - 2.7 V to 3.6 V (NEO-M8N/Q)
  • - Power consumption4 23 mA @ 3.0 V (continuous)
  • - 5 mA @ 3.0 V Power Save Mode (1 Hz, GPS mode only)
  • - Backup Supply 1.4 to 3.6 V

  • - NEO-M8N-0 u-blox M8 Concurrent GNSS LCC Module,
  • - TCXO, flash, SAW, LNA,
  • - Timepulse Configurable 0.25 Hz to 10 MHz

We left a connector for APM for extra,If you need used for APM,you can install the connector by yourself or leave us a message ,we will change for you . Original connector is for Pixhawk flight control board my friend!

Downloads

Reviews (0)

Write a review

Note: HTML is not translated!
    Bad           Good
Note : Images shown is only for representation. The actual product may vary with the picture shown.